CoatingsPro Magazine Supplements

Concrete Dec 2018

CoatingsPro offers an in-depth look at coatings based on case studies, successful business operation, new products, industry news, and the safe and profitable use of coatings and equipment.

Issue link: https://coatingspromag.epubxp.com/i/1062329

Contents of this Issue

Navigation

Page 14 of 43

SPONSORED CONTENT 15 COATINGSPRO CONCRETE COVERED DECEMBER 2018 Concrete Proof used, General Equipment offers the SG24/GH, featuring an 11-hp Honda engine. Bosch also supplies a wide range of angle grinders, including its 4.5-inch (11.4 cm) GWS18V- 45PSC grinder. To clean up at the end of surface preparation and prior to applying a new system, vacuums such as the 2.6-gallon (9.8 L) GAS18V-3N 18V cordless wet/dry vacuum cleaner from Bosch with a washable HEPA filter can be used for thorough jobsite cleanup. "Surface prep is what we emphasize to contractors as the most important piece of long-term success of the flooring," said Ball of Sherwin-Williams. Even if there are moisture issues, one way you can combat that is good surface prep, so that there are more good bond sites to keep that coating bonded. W hether it's a shot blaster or even a grinder, and the different tooling that's out there, there's no question that surface prep is going to be the key." Coating Choices With the surface prepared, the new coating system at a concrete jobsite typically consists of some combination of coatings and penetrating sealers. Among coatings, popular General Equipment also offers a smaller surface grinder: SG24. This is offered in an electric version for when gas isn't an option, as well as a gas version for when it is. Surface prep needs to be supported by equipment, perhaps by Bosch. As Casey Ball, flooring market segment director of Sherwin-Williams said, "There's no question that surface prep is going to be the key." VENDOR TEAM 3M Safety equipment manufacturer 2501 Hudson Rd. Maplewood, MN 55144 (800) 364-3577 www.3m.com American Concrete Institute (ACI) Education 38800 Country Club Dr. Farmington Hills, MI 48331 (248) 848-3700 www.concrete.org American National Standards Institute (ANSI) Education 1899 L St. NW, 11 th Floor Washington, D.C. 20036 (202) 293-8020 www.ansi.org Arizona Polymer Flooring Material manufacturer 4565 W Watkins St. Phoenix, AZ 85043 (800) 562-4921 www.apfepoxy.com BlastPro Manufacturing, Inc. Equipment manufacturer 513 Beacon Pl. Oklahoma City, OK 73127 (405) 491-6464 www.blastpromfg.com Blastrac, NA Equipment manufacturer 13201 N Santa Fe Ave. Oklahoma City, OK 73114 (800) 256-3440 www.blastrac.com The Brush Man, LLC Equipment manufacturer 602 W Hickory St. Mahomet, IL 61853 (800) 274-6898 www.brushman.com Bullard Safety equipment manufacturer 1898 Safety Way Cynthiana, KY 41031 (877) 285-5273 www.bullard.com ChemMasters Material manufacturer 300 Edwards St. Madison, OH 44057 (440) 428-2105 www.chemmasters.net Coatings for Industry, Inc. (CFI) Coatings manufacturer 319 Township Line Rd. Souderton, PA 18964 (877) 723-0919 www.cficoatings.com DeFelsko Equipment manufacturer 800 Proctor Ave. Ogdensburg, NY 13669 (800) 448-3835 www.defelsko.com DeWalt Equipment manufacturer 701 E Joppa Rd. Baltimore, MD 21286 (800) 433-9258 www.dewalt.com Diamatic USA Equipment manufacturer 5220 Gaines St. San Diego, CA 92110 (866) 295-5512 www.diamaticusa.com Easycove Material manufacturer 872 S Milwaukee Ave., Ste. 234 Libertyville, IL 60048 (847) 972-2131 www.easycove.com Eco-Cove Material manufacturer 5612 2nd St. W, Ste. 2 Lehigh Acres, FL 33971 (239) 303-7378 www.eco-cove.com Elcometer Inc. Equipment manufacturer 1893 Rochester Industrial Dr. Rochester Hills, MI 48309 (248) 650-0500 www.elcometer.com

Articles in this issue

Links on this page

Archives of this issue

view archives of CoatingsPro Magazine Supplements - Concrete Dec 2018